VersEseal Gutter & Roof Sealant

Both VersEseal Rapid Build and VersEseal Top Coat are water based however, gloves, eye protections and overalls are recommended. Please read the full Safety Data Sheet before use.

If the roof is used for water collection, allow 10 days curing and discard the first two rains or rinses.

1. Remove any old, failed sealant with a scraper, if possible. If it can’t be removed, treat the area like a gap and reinforce with geofabric as below

2. Wash down to remove all dirt, dust and grime. A pressure washer is ideal for this. Allow to dry.

3. Lightly abrade the surface to maximise adhesion, use a medium grit sand paper. Wipe with a damp cloth to remove sanding dust.

4. Apply masking tape to give a clean edge to areas that are not to be coated. PROTIP: Remove masking tape while the coating is still wet and re-mask for each coat.

5. Prepare Geofabric to reinforce along joins, around penetrations and over old sealant. It is much easier to pre-cut geofabric to size before starting to coat the membrane.

6. Brush the first coat of VersEseal Rapid Build liquid rubber over areas that need repair or additional reinforcement. Aim for a good thick coating. Remember, you’re waterproofing, not painting – thick is good!

7. Lay geofabric bandage into the wet coating over joins and around penetrations. Ensure it is smooth with no creases or air pockets. You may need to cut a nick to allow the bandage to neatly conform to any corners or bends. If the fabric overlaps, paint some VersEseal Rapid Build liquid rubber between the layers to glue it together.

8. Immediately brush a second coat of VersEseal Rapid Build liquid rubber aiming again for another good thick coating to give a wet on wet sandwich with a total wet coating thickness of 1mm.

9. Allow the repaired area to dry. This will typically take about 4 hours at 25℃ with good ventilation.

10. The final sealing step will depend on the condition of your roof.

• ENTIRE ROOF – Apply two generous coats of VersEseal Rapid Build liquid rubber over the entire roof to achieve a final Dry Film Thickness (DFT) of 0.6mm over the main roof area and 1.2mm over joints and repaired areas. Apply the first coat North-South and the second coat East-West. Allow to dry for at least 4hrs between coats of VersEseal Rapid Build Membrane. After final coat of VersEseal Rapid Build Membrane, allow to dry for 96hrs before applying VersEseal Top Coat – assuming good drying conditions of 25℃ and good ventilation.
• REPAIR ONLY – If your roof is sound apart from the areas that have been repaired: Apply a third good thick coat of VersEseal Rapid Build liquid rubber over the repaired areas, to achieve a final Dry Film Thickness (DFT) of 1.2mm and allow to dry, allow to dry for 96hrs before applying VersEseal Top Coat – assuming good drying conditions of 25℃ and good ventilation.

11. Allow the VersEseal Rapid Build membrane to dry for a minimum of 96hrs in good drying conditions (25℃ with good ventilation / breeze). If conditions are not optimal a longer drying time will be required – actual times will vary depending on season and location. If you are unsure or would like further guidance on this please give us a call.

NOTE: VersEseal Rapid Build should be applied at a minimum total wet coating of 1kg/m2. Ensure this correct coating thickness is achieved to provide longevity.

12. Using a clean brush or roller, apply the first coat of VersEseal Top Coat over the Rapid Build Waterproofing. This may show some bleed through from the black colour underneath. Allow to dry, typically this will take 2 hours at 25℃ with good ventilation.

13. Apply the second coat of VersEseal Top Coat and allow to dry. A third coat may be required depending on application technique to achieve full coverage.

14. The final product should have a DFT of 0.5mm of Top Coat on top of the VersEseal Rapid Build.

15. Allow VersEseal Top Coat to dry for 24 hours in good drying conditions (25C with good ventilation / breeze as described above)

NOTE: VersEseal Top Coat should be applied at a minimum total wet coating of 1kg/m2. Ensure this correct coating thickness is achieved to provide longevity. 

Do not use this water based VOC Free coating system if rain or heavy dew are expected before fully dried. Apply at temperatures between 10℃ and 30℃. Avoid applying during the hottest part of the day.

For Cleaning up, use mineral turpentine to clean VersEseal Rapid Build from hard surfaces, use Baby Oil (Mineral oil) to clean from skin. Verseseal Top Coat can be cleaned with water.